Brass Bands and Ensembles

Writing for Brass: Ranges, Transpositions and Voicing Tips

How to write for brass: approximate ranges, transposition for trumpet, horn and other instruments, voicing for balance, and breath and endurance tips.

On this page
  1. What is brass in music?
  2. How brass instruments make a sound
  3. Approximate ranges of the main instruments
  4. Transposition explained
  5. Voicing for balance
  6. Breath, endurance and mutes
  7. Checking a part before rehearsal

This guide is for composers, arrangers and students who need to write a short brass part or a full brass section. It covers what brass is, how the instruments make sound, rough ranges, transposition, voicing and a few practical checks. Ranges vary from player to player, so treat the numbers here as starting points rather than limits.

What is brass in music?

In music, brass is a family of instruments that produce sound through the player’s lips vibrating in a cup-shaped or funnel-shaped mouthpiece. Most are made of brass or other metal. The main members are the trumpet, cornet, horn, trombone, euphonium and tuba, and the full list of brass instruments covers the rest. Their pitch is changed by valves or a slide, or in the case of the horn, by valves together with the player’s hand in the bell.

For how the orchestral family is put together, see what instruments are in the brass family orchestra.

How brass instruments make a sound

Brass players buzz their lips into the mouthpiece. The lips act as the vibrating part, a role a reed plays in a woodwind. That vibration sets the air column inside the tube into motion. Changing the tension of the lips, the air speed and the valve or slide position selects the note.

This is why brass players spend so much time on embouchure and breath. Small changes in lip tension can move a note by a large interval, and the air supply sets the volume and the tone.

Approximate ranges of the main instruments

Brass ranges depend on the player and the instrument. As rough guides:

  • Trumpet: roughly from E3 to C6 for most players (see the trumpet range guide), with the top of the range demanding.
  • Horn: parts usually sit in the middle of the stave, with occasional low or high notes that need a lot of air or control.
  • Tenor trombone: roughly from E2 to about B♭4 as written.
  • Tuba: the lowest notes sit near the bottom of the bass clef. Top notes are usually in the middle of the staff.

These are approximate. Check the range of the actual player’s instrument, and use a method book or range chart if you need precise limits.

Transposition explained

Many brass instruments are built in a key other than C, so the written note is not the sounding note.

  • B♭ trumpet and cornet: a written C sounds B♭, a major second lower. The Bb trumpet transposition chart lists every note.
  • F horn: a written C sounds F, a perfect fifth lower.
  • E♭ alto horn (tenor horn in UK bands): a written C sounds E♭, a major sixth lower.
  • Trombone (tenor and bass): non-transposing, so the written note is the sounding note.
  • Tuba: the C tuba is non-transposing. B♭ and E♭ tubas are transposed, and their clef and octave can differ from the sounding pitch. Check the markings on the part.

Always check the instrument on the part and whether it is written at sounding pitch or transposed.

Voicing for balance

Trumpets sit above the rest of the brass and can easily overpower the other sections. When they play with the lower brass, a softer dynamic usually balances the group better.

Wide spacing in the low register helps keep chords clear. Close voicings low down can sound muddy, especially with tuba and low trombone. Horns blend well with woodwinds and strings, and a horn and trombone playing in unison blend well too. Trumpets cut through, so they are often used for melody or for the top of a chord.

When writing for brass with strings or woodwinds, remember that the brass sound is strong. Using a mute or a softer dynamic can keep the balance right.

Breath, endurance and mutes

Give players breaths in long phrases, and avoid long stretches of high or loud playing. Trumpet and high horn parts tire players quickly.

Mute changes take a moment to make, so allow a small gap if the change happens in a fast passage. Common mutes include the straight mute, the cup mute, the Harmon mute and the plunger. Each one changes the tone in a different way.

Fast double tonguing and very rapid passages are specialist skills on brass. Write them with care, and check them with a player if you can.

Checking a part before rehearsal

Before a rehearsal, check the transposition, clef, key signature and breath marks. Ask a player to read the part if you can, and compare the notes with the instrument’s real range.

Computer playback is useful for checking notes and rhythm, but it cannot show the real problems of endurance, balance or breath. A short read-through with real players will show those faster.

The complete guide to brass bands and ensembles

Brass Band Sections: Every Part and Instrument Explained
Read the guide

Keep exploring

Guides from other topics

All topics →