Short answer
A trombone makes sound the way other brass instruments do. The player buzzes their lips into a cup-shaped mouthpiece. That buzz sets the air inside the tubing vibrating, and the bell sends the sound out. The slide changes the length of the tubing, which changes the pitch. Each slide position lowers the note by about one semitone on the same harmonic. Lip tension and air speed choose which harmonic sounds.
Step 1: The lip buzz
The mouthpiece is a detachable cup that sits in the leadpipe. Your lips press into it and buzz. That buzz is the source of the sound. The mouthpiece also has a narrow constriction called a venturi, which adds resistance and affects the tone. Mouthpieces vary in cup depth, rim shape, and throat, so the same trombone can sound and feel different with another mouthpiece.
Step 2: The air column and the bell
The tubing is a long, mostly cylindrical tube with two U-shaped bends. With the slide fully in, a tenor trombone’s tubing is about 9 feet long. The air inside vibrates in patterns called standing waves, and the length of the tube and the player’s lips decide which patterns can sound. The bell at the end flares outward. The flare helps the sound project into the room.
Step 3: The slide sets the tube length
The slide has an inner tube and an outer tube. Moving the slide out makes the air column longer, and a longer column gives a lower pitch. There are seven positions, from 1st (slide fully in, closest to the player) to 7th (slide fully out). Each position lowers the pitch by about one semitone on the same harmonic, so 7th position sits about a tritone, six semitones, below 1st.
Because the slide can stop at any point, it can move smoothly from one note to another. That is what makes a glissando possible. The trombone slide positions chart lists the note for each position.
Step 4: The lips choose the harmonic
The slide chooses the length, and the lips choose the harmonic. Tightening the lips and increasing air speed moves the sound up to a higher harmonic. On a B♭ trombone in first position, the harmonics give B♭2, F3, B♭3, D4, and F4. The slide does not move between these. The lips do.
Lip bends can also move a note up or down by about a semitone without moving the slide. That is one reason a slightly out-of-place slide can often be corrected by ear.
Step 5: Alternate positions and small corrections
Not every harmonic sits exactly where equal temperament puts it, so players adjust the slide slightly for some notes. Many notes can also be played in more than one slide position. These alternate positions cut down on slide movement in fast passages.
The main parts of a trombone
- Mouthpiece: the detachable cup the lips buzz into.
- Leadpipe: holds the mouthpiece and leads the air into the slide.
- Neckpipe: connects the leadpipe to the slide section.
- Slide: the inner and outer tubes that the player moves.
- Bell section (back bow): the U-bend and bell. The tuning slide sits here.
- Ferrule: the joint, with a threaded collar, that connects the slide to the bell section.
- Bracing (stays): braces that hold the slide tubes in line.
- F attachment: on many tenor and bass trombones, a trigger-operated loop of extra tubing that lowers the instrument and reaches low notes.
Why a trombone uses a slide
Almost all trombones use a slide because it gives continuous control of pitch. Valves make fixed steps, but the slide can stop anywhere, which allows glissandos and small adjustments. The slide traces back to the sackbut, the Renaissance and Baroque ancestor of the modern trombone.
Some trombones do add valves. A slide-only trombone has a gap in its lowest range, so many tenor and bass trombones add an F attachment to fill that gap. A separate instrument, the valve trombone, uses three valves in place of the slide.
Where to go next
- Trombone slide positions chart gives the note for each position on each harmonic.
- Bass trombone glissando chart shows which slides stay smooth.
- Switching from trumpet to trombone explains what changes for trumpet players.